Sound Sensor - Revision history

Admin: /* Overview */

2012-09-17T02:54:19Z

Overview

← Older revision		Revision as of 02:54, 17 September 2012
Line 2:		Line 2:
	[[File:Sound sensor.jpg\|300px]]		[[File:Sound sensor.jpg\|300px]]

	The Sound sensor module is a simple microphone based on a opamp LM358 to amplify the sound strength of the environment like door knocks, etc loud enough to be picked up by a microcontroller's Analog to Digital converter. The value of output can be adjusted by the potentiometer.		The Sound sensor module is a simple microphone based on a opamp LM358 to amplify the sound strength of the environment like door knocks and etc loud enough to be picked up by a microcontroller's Analog to Digital converter. The value of output can be adjusted by the potentiometer.

	==Applications==		==Applications==

Admin: /* Connection Diagram */

2012-09-17T02:53:12Z

Connection Diagram

← Older revision		Revision as of 02:53, 17 September 2012
Line 9:		Line 9:

	==Connection Diagram==		==Connection Diagram==
			Here is the guide illustrates how to connect an Arduino to the sound sensor. The following is a table describing which pins on the Arduino should be connected to the pins on the sound sensor:


	[[File:BT.jpg]]		[[File:BT.jpg]]

Admin: /* Connection Diagram */

2012-09-17T02:51:56Z

Connection Diagram

← Older revision		Revision as of 02:51, 17 September 2012
Line 11:		Line 11:
	[[File:BT.jpg]]		[[File:BT.jpg]]

	VCC ------- VCC		VCC <-------> VCC
	GND ------- GND		GND <-------> GND
	S ----- Analog 0		S <-------> Analog 0

	==Examples==		==Examples==

Admin: /* Connection Diagram */

2012-09-17T02:51:21Z

Connection Diagram

← Older revision		Revision as of 02:51, 17 September 2012
Line 11:		Line 11:
	[[File:BT.jpg]]		[[File:BT.jpg]]

	VCC ----- VCC		VCC ------- VCC
	GND ----- GND		GND ------- GND
	S ----- Analog 0		S ----- Analog 0

Admin: /* Connection Diagram */

2012-09-17T02:50:53Z

Connection Diagram

← Older revision		Revision as of 02:50, 17 September 2012
Line 10:		Line 10:
	==Connection Diagram==		==Connection Diagram==
	[[File:BT.jpg]]		[[File:BT.jpg]]

			VCC ----- VCC
			GND ----- GND
			S ----- Analog 0

	==Examples==		==Examples==

Admin: /* Overview */

2012-09-17T02:47:34Z

Overview

← Older revision		Revision as of 02:47, 17 September 2012
Line 1:		Line 1:
	==Overview==		==Overview==
	[[File:Sound sensor.jpg]]		[[File:Sound sensor.jpg\|300px]]

	The Sound sensor module is a simple microphone based on a opamp LM358 to amplify the sound strength of the environment like door knocks, etc loud enough to be picked up by a microcontroller's Analog to Digital converter. The value of output can be adjusted by the potentiometer.		The Sound sensor module is a simple microphone based on a opamp LM358 to amplify the sound strength of the environment like door knocks, etc loud enough to be picked up by a microcontroller's Analog to Digital converter. The value of output can be adjusted by the potentiometer.

	==Applications==		==Applications==

Admin at 02:47, 17 September 2012

2012-09-17T02:47:16Z

← Older revision		Revision as of 02:47, 17 September 2012
Line 1:		Line 1:
	==Overview==		==Overview==
			[[File:Sound sensor.jpg]]

	The Sound sensor module is a simple microphone based on a opamp LM358 to amplify the sound strength of the environment like door knocks, etc loud enough to be picked up by a microcontroller's Analog to Digital converter. The value of output can be adjusted by the potentiometer.		The Sound sensor module is a simple microphone based on a opamp LM358 to amplify the sound strength of the environment like door knocks, etc loud enough to be picked up by a microcontroller's Analog to Digital converter. The value of output can be adjusted by the potentiometer.

Line 7:		Line 9:

	==Connection Diagram==		==Connection Diagram==
			[[File:BT.jpg]]

	==Examples==		==Examples==

Admin at 01:57, 17 September 2012

2012-09-17T01:57:12Z

← Older revision		Revision as of 01:57, 17 September 2012
Line 3:		Line 3:

	==Applications==		==Applications==
	Simple microphone		*Simple microphone
	Sound detection		*Sound detection

	==Connection Diagram==		==Connection Diagram==

	==Examples==		==Examples==
	void setup()		void setup()
	{		{
	Serial.begin(9600); // open serial port, set the baud rate to 9600 bps		Serial.begin(9600); // open serial port, set the baud rate to 9600 bps
	}		}
	void loop()		void loop()
	{		{
	int val;		int val;
	val=analogRead(0); //connect mic sensor to Analog 0		val=analogRead(0); //connect mic sensor to Analog 0
	Serial.println(val,DEC);//print the sound value to serial		Serial.println(val,DEC);//print the sound value to serial
	delay(100);		delay(100);
	}		}

	==How to buy==		==How to buy==
	Click here to buy [http://www.geeetech.com/analog-voice-sound-sensor-module-p-600.html Sound sensor]		Click here to buy [http://www.geeetech.com/analog-voice-sound-sensor-module-p-600.html Sound sensor]

Admin: Created page with "==Overview== The Sound sensor module is a simple microphone based on a opamp LM358 to amplify the sound strength of the environment like door knocks, etc loud enough to be pic..."

2012-09-17T01:56:44Z

Created page with "==Overview== The Sound sensor module is a simple microphone based on a opamp LM358 to amplify the sound strength of the environment like door knocks, etc loud enough to be pic..."

New page

==Overview==
The Sound sensor module is a simple microphone based on a opamp LM358 to amplify the sound strength of the environment like door knocks, etc loud enough to be picked up by a microcontroller's Analog to Digital converter. The value of output can be adjusted by the potentiometer.

==Applications==
Simple microphone
Sound detection

==Connection Diagram==

==Examples==
void setup()
{
Serial.begin(9600); // open serial port, set the baud rate to 9600 bps
}
void loop()
{
int val;
val=analogRead(0); //connect mic sensor to Analog 0
Serial.println(val,DEC);//print the sound value to serial
delay(100);
}

==How to buy==
Click here to buy [http://www.geeetech.com/analog-voice-sound-sensor-module-p-600.html Sound sensor]