Mini2440‘s settings and connections - Revision history

Admin: /* Hyper terminal setting */

2012-06-18T09:28:46Z

Hyper terminal setting

← Older revision		Revision as of 09:28, 18 June 2012
Line 24:		Line 24:
	In addition, please make sure to use the accessory direct serial port cable, perhaps other cable may not work. <br>		In addition, please make sure to use the accessory direct serial port cable, perhaps other cable may not work. <br>

	We must use a terminal application or similar to communicate with development board via serial port. The HyperTerminal included with Windows XP is ~~the~~ common use. Usually the Linux for desktop also carry the similar serial terminal application called minicom based on the command line. <br>		We must use a terminal application or similar to communicate with development board via serial port. The HyperTerminal included with Windows XP is in common use. Usually the Linux for desktop also carry the similar serial terminal application called minicom based on the command line. <br>

	Here we focus on the HyperTerminal included with Windows XP. HyperTerminal is usually located in “Start>Programs>Accessories>Communications”. Run this application, then the following dialog box appears, click “Cancel”.		Here we focus on the HyperTerminal included with Windows XP. HyperTerminal is usually located in “Start>Programs>Accessories>Communications”. Run this application, then the following dialog box appears, click “Cancel”.

Admin: /* Startup mode selection */

2012-06-18T09:19:22Z

Startup mode selection

← Older revision		Revision as of 09:19, 18 June 2012
Line 15:		Line 15:

	==Startup mode selection==		==Startup mode selection==
	The startup mode of Mini2440 is chosen by a toggle switch S2. <br>		The startup mode of Mini2440 is chosen by toggle switch S2. <br>
	S2 is toggled to Nor Flash, the system will boot from Nor Flash. <br>		S2 is toggled to Nor Flash, the system will boot from Nor Flash. <br>
	S2 is toggled to Nand Flash, the system will boot from Nand Flash. <br>		S2 is toggled to Nand Flash, the system will boot from Nand Flash. <br>

Admin: /* Startup mode selection */

2012-06-18T09:18:55Z

Startup mode selection

← Older revision		Revision as of 09:18, 18 June 2012
Line 15:		Line 15:

	==Startup mode selection==		==Startup mode selection==
	The startup mode of Mini2440 is ~~choose~~ by a toggle switch S2. <br>		The startup mode of Mini2440 is chosen by a toggle switch S2. <br>
	S2 is toggled to Nor Flash, the system will boot from Nor Flash. <br>		S2 is toggled to Nor Flash, the system will boot from Nor Flash. <br>
	S2 is toggled to Nand Flash, the system will boot from Nand Flash. <br>		S2 is toggled to Nand Flash, the system will boot from Nand Flash. <br>

Admin at 09:16, 18 June 2012

2012-06-18T09:16:53Z

← Older revision		Revision as of 09:16, 18 June 2012
Line 44:		Line 44:
	[[File:2440setting 5.jpg]]		[[File:2440setting 5.jpg]]

	Finally, the most important thing is to set serial port. Note that the Flow control must be specified as none, or you will see the data output and no data input.		Finally, the most important thing is to set serial port. Note that the Flow control must be specified as none, or you will see the data output and no data input. The serial baud rate must set at 115200.

	[[File:2440setting 6.jpg]]		[[File:2440setting 6.jpg]]

Admin at 09:14, 18 June 2012

2012-06-18T09:14:12Z

← Older revision		Revision as of 09:14, 18 June 2012
Line 36:		Line 36:
	[[File:2440setting 3.jpg]]		[[File:2440setting 3.jpg]]

	HyperTerminal will ask you to name the new connection and we name it “ttys0”, ~~windows~~ prohibit you from naming it “COM1” or similar due to the name has been occupied by system.		HyperTerminal will ask you to name the new connection and we name it “ttys0”, Windows XP prohibit you from naming it “COM1” or similar due to the name has been occupied by system.

	[[File:2440setting 4.jpg]]		[[File:2440setting 4.jpg]]
Line 48:		Line 48:
	[[File:2440setting 6.jpg]]		[[File:2440setting 6.jpg]]

	After all setting is complete, switch on the power supply and the HyperTerminal shows the vivi startup, then select ”File>Save as” in HyperTerminal to save the connection settings so as ~~not~~ to ~~set~~ it ~~again~~.		After all setting is complete, switch on the power supply and the HyperTerminal shows the vivi startup, then select ”File>Save as” in HyperTerminal to save the connection settings so as to use it next time.

	[[File:2440setting 7.jpg]]		[[File:2440setting 7.jpg]]

Admin: /* External connection */

2012-06-18T09:11:40Z

External connection

← Older revision		Revision as of 09:11, 18 June 2012
Line 10:		Line 10:
	*Please use the crossed network cable we provide to connect network interface on Mini2440 with PC		*Please use the crossed network cable we provide to connect network interface on Mini2440 with PC
	*Please use the 5V power adapter we provide to connect the power jack on Mini2440		*Please use the 5V power adapter we provide to connect the power jack on Mini2440
	*~~please~~ plug the headphone or speaker jack in the audio output socket (green).		*Please plug the headphone or speaker jack in the audio output socket (green).
	*If you have a LCD display, please connect it to LCD interface on mini2440 following the direct of the dataline.		*If you have a LCD display, please connect it to LCD interface on mini2440 following the direct of the dataline.
	*~~please~~ use USB cable to connect mini2440 with PC.		*Please use USB cable to connect mini2440 with PC.

	==Startup mode selection==		==Startup mode selection==

Admin: /* External jack connection */

2012-06-18T09:11:24Z

External jack connection

← Older revision		Revision as of 09:11, 18 June 2012
Line 6:		Line 6:
	The operation below is based on WinXP environment. Supervivi-64M included in CD-ROM should be applied to 64M mini2440, supervivi-128M should be applied to 128M/256M/512M/1GB mini2440.		The operation below is based on WinXP environment. Supervivi-64M included in CD-ROM should be applied to 64M mini2440, supervivi-128M should be applied to 128M/256M/512M/1GB mini2440.

	==External ~~jack~~ connection==		==External connection==
	*Please use the direct serial port cable we provide to connect serial port 0 on Mini2440 with PC serial port.		*Please use the direct serial port cable we provide to connect serial port 0 on Mini2440 with PC serial port.
	*Please use the crossed network cable we provide to connect network interface on Mini2440 with PC		*Please use the crossed network cable we provide to connect network interface on Mini2440 with PC

Admin: Created page with "Mini2440 development board’s settings and connections == Note == We have installed Linux system which includes three files in accordance with supervivi, zImage_t35/x35/w35 ..."

2012-06-18T09:10:50Z

Created page with "Mini2440 development board’s settings and connections == Note == We have installed Linux system which includes three files in accordance with supervivi, zImage_t35/x35/w35 ..."

New page

Mini2440 development board’s settings and connections

== Note ==
We have installed Linux system which includes three files in accordance with supervivi, zImage_t35/x35/w35 and rootfs-qtopia-qt4.img in CD-ROM by default if the customer didn’t specify which system to be installed. 

The operation below is based on WinXP environment. Supervivi-64M included in CD-ROM should be applied to 64M mini2440, supervivi-128M should be applied to 128M/256M/512M/1GB mini2440.

==External jack connection==
*Please use the direct serial port cable we provide to connect serial port 0 on Mini2440 with PC serial port.
*Please use the crossed network cable we provide to connect network interface on Mini2440 with PC
*Please use the 5V power adapter we provide to connect the power jack on Mini2440
*please plug the headphone or speaker jack in the audio output socket (green).
*If you have a LCD display, please connect it to LCD interface on mini2440 following the direct of the dataline.
*please use USB cable to connect mini2440 with PC.

==Startup mode selection==
The startup mode of Mini2440 is choose by a toggle switch S2. 
S2 is toggled to Nor Flash, the system will boot from Nor Flash. 
S2 is toggled to Nand Flash, the system will boot from Nand Flash. 

==Hyper terminal setting==
Note: Some customers use USB-RS232 cable to expand Serial port, please note that a few USB-RS232 cables will result in error code because of its poor quality. Our customers could contact with our sales agents to buy the cable available they provide. 

In addition, please make sure to use the accessory direct serial port cable, perhaps other cable may not work. 

We must use a terminal application or similar to communicate with development board via serial port. The HyperTerminal included with Windows XP is the common use. Usually the Linux for desktop also carry the similar serial terminal application called minicom based on the command line. 

Here we focus on the HyperTerminal included with Windows XP. HyperTerminal is usually located in “Start>Programs>Accessories>Communications”. Run this application, then the following dialog box appears, click “Cancel”.

[[File:2440setting 1.jpg]]

Next click “Yes” in the popup window.

[[File:2440setting 2.jpg]]

[[File:2440setting 3.jpg]]

HyperTerminal will ask you to name the new connection and we name it “ttys0”, windows prohibit you from naming it “COM1” or similar due to the name has been occupied by system.

[[File:2440setting 4.jpg]]

After that another dialog box pop up again, you need to specify the serial port of the development board and we specify “COM1” as shown.

[[File:2440setting 5.jpg]]

Finally, the most important thing is to set serial port. Note that the Flow control must be specified as none, or you will see the data output and no data input.

[[File:2440setting 6.jpg]]

After all setting is complete, switch on the power supply and the HyperTerminal shows the vivi startup, then select ”File>Save as” in HyperTerminal to save the connection settings so as not to set it again.

[[File:2440setting 7.jpg]]