Me Creator - Revision history

Admin: /* detailes 0f me creator */

2016-04-18T06:47:42Z

detailes 0f me creator

← Older revision		Revision as of 06:47, 18 April 2016
Line 568:		Line 568:
	Finally, to ensure all filament dust is removed from the extruder assembly, you can use a can of compressed air to flush out any remaining filament dust.		Finally, to ensure all filament dust is removed from the extruder assembly, you can use a can of compressed air to flush out any remaining filament dust.

	==detailes 0f me creator==		==detailes of me creator==
	<gallery>		<gallery>
	Image:IMG 6640.jpg\| <center>Internally installed LED strips</center>		Image:IMG 6640.jpg\| <center>Internally installed LED strips</center>

2015-12-01T10:05:11Z

Technical Specifications

2015-07-30T03:21:00Z

connect power supply

← Older revision		Revision as of 03:21, 30 July 2015
Line 143:		Line 143:

	2. Loose the screws on the connector,then screw the wires up in order, you can refer to the color of the wire, as shown in the following picture.		2. Loose the screws on the connector,then screw the wires up in order, you can refer to the color of the wire, as shown in the following picture.



			[[File:Power supply1.JPG\|500px]]

	<font color=red>		<font color=red>
Line 156:		Line 160:

	</font>		</font>

	~~[[File:Power supply1.JPG\|500px]]~~

	[[File:Power supply wiring.JPG\|500px]]		[[File:Power supply wiring.JPG\|500px]]

2015-07-30T03:20:40Z

connect power supply

← Older revision		Revision as of 03:20, 30 July 2015
Line 157:		Line 157:
	</font>		</font>

	[[File:Power supply1.JPG\|500px]] [[File:Power supply wiring.JPG\|500px]]		[[File:Power supply1.JPG\|500px]]

			[[File:Power supply wiring.JPG\|500px]]

	==Install the drivers and software==		==Install the drivers and software==

2015-07-30T03:20:23Z

connect power supply

← Older revision		Revision as of 03:20, 30 July 2015
Line 144:		Line 144:
	2. Loose the screws on the connector,then screw the wires up in order, you can refer to the color of the wire, as shown in the following picture.		2. Loose the screws on the connector,then screw the wires up in order, you can refer to the color of the wire, as shown in the following picture.

			<font color=red>
	L -- brown		L -- brown

Line 154:		Line 155:
	+ V -- red		+ V -- red

	~~[[File:Power supply1.JPG]] [[File:Power supply wiring.JPG]]~~		</font>


			[[File:Power supply1.JPG\|500px]] [[File:Power supply wiring.JPG\|500px]]

	==Install the drivers and software==		==Install the drivers and software==

2015-07-30T03:19:25Z

Install the drivers and software

← Older revision		Revision as of 03:19, 30 July 2015
Line 137:		Line 137:

	*ONLY OPERATE YOUR ME CREATOR PRINTER IN A WELL-VENTILATED SPACE AWAY FROM MOISTURE AND HEAT SOURCES WITH A WORKING SMOKE/FIRE ALARM.		*ONLY OPERATE YOUR ME CREATOR PRINTER IN A WELL-VENTILATED SPACE AWAY FROM MOISTURE AND HEAT SOURCES WITH A WORKING SMOKE/FIRE ALARM.

			==connect power supply==

			1.Take out the powersupply unit, check the condition of it and check it is 220V or 110V, you can switch it according to your real situation. this is very inportant.

			2. Loose the screws on the connector,then screw the wires up in order, you can refer to the color of the wire, as shown in the following picture.

			L -- brown

			N -- blue

			GND -- yellow

			COM -- black

			+ V -- red

			[[File:Power supply1.JPG]] [[File:Power supply wiring.JPG]]



	==Install the drivers and software==		==Install the drivers and software==

2015-07-14T08:04:30Z

Install the drivers

← Older revision		Revision as of 08:04, 14 July 2015
Line 155:		Line 155:
	'''Windows Manual Install'''		'''Windows Manual Install'''

	Note: In some cases the drivers will not install on their own. The drivers for Windows can be found ~~in the following link:~~ [~~[Media~~:~~Serial install~~.~~zip ]~~]		Note: In some cases the drivers will not install on their own. The drivers for Windows can be found
			[http://www.ftdichip.com/Drivers/CDM/CDM%20v2.12.00%20WHQL%20Certified.exe here]

	If the driver was not automatically installed, you may see this screen:		If the driver was not automatically installed, you may see this screen:

2015-05-14T09:29:25Z

slic3r setting test

← Older revision		Revision as of 09:29, 14 May 2015
Line 346:		Line 346:

	4. Find the ini file in your computer. and you can see the parameters changed accordingly.		4. Find the ini file in your computer. and you can see the parameters changed accordingly.

			[[File:Slicer setting load 2.jpg]]

	5. You can download the configure file here.[[Media:MeCreator.rar]]		5. You can download the configure file here.[[Media:MeCreator.rar]]


	==Leveling The Print Bed==		==Leveling The Print Bed==

2015-05-14T09:24:20Z

Leveling The Print Bed

← Older revision		Revision as of 09:24, 14 May 2015
Line 328:		Line 328:

	[[File:ManualControl2.png]][[File:Screen-shot-2013-11-18-at-9.27.00-PM.png]]		[[File:ManualControl2.png]][[File:Screen-shot-2013-11-18-at-9.27.00-PM.png]]

			===slic3r setting test===

			1. Open your Repetier Host and click ''slicer'' and ''configure''

			[[File:Slicer setting1.jpg]]

			2. you can see the slicer confirure pannel now.

			[[File:Slicer setting2.jpg]]

			3.Now you can load the ini file into the slicer or configure the parameters one by one, firt let's see how to load the file.

			step 1. click ''file''> ''load Config''

			[[File:Slicersetting load.jpg]]

			4. Find the ini file in your computer. and you can see the parameters changed accordingly.

			5. You can download the configure file here.[[Media:MeCreator.rar]]


	==Leveling The Print Bed==		==Leveling The Print Bed==

2015-05-05T06:49:20Z

How to control on LCD

← Older revision		Revision as of 06:49, 5 May 2015
Line 408:		Line 408:

	'''3.How to move the axis and extruder motor separately'''<br>		'''3.How to move the axis and extruder motor separately'''<br>
	:Press the button>”Prepare”>”Move axis”>”Move 10mm/1mm/0.1mm”>”Move X/Y/Z/extruder”<br>		:Press the button>”Prepare”>”Move axis”>”Move 10mm/1mm/0.1mm”>”Move X/Y/Z/extruder”>Rotate the button>Press the button<br>
	<font color="red">Note: The extruder motor can not move unless the temperature is more than 180 degrees.</font><br>		<font color="red">Note: The extruder motor can not move unless the temperature is more than 180 degrees.</font><br>
	[[File:LCD prepare.png\|400px]]<br>		[[File:LCD prepare.png\|400px]]<br>