LilyPad Xbee - Revision history

Admin: /* Features */

2015-08-28T01:01:06Z

Features

← Older revision		Revision as of 01:01, 28 August 2015
Line 10:		Line 10:
	Power supply:3.3V or 5V.If you have a power device who supplies 2V to 6V ,you should connect to “+” not the “3.3V” interface ,if the power is 3.3v you can connect to 3.3V interface directly.		Power supply:3.3V or 5V.If you have a power device who supplies 2V to 6V ,you should connect to “+” not the “3.3V” interface ,if the power is 3.3v you can connect to 3.3V interface directly.
	Frequency :The frequency reaches up to 2.4GHZ		Frequency :The frequency reaches up to 2.4GHZ
	Current Limiting Protection		Current Limiting Protection


			==Download ==
			[http://www.ftdichip.com/Drivers/CDM/CDM%20v2.12.00%20WHQL%20Certified.exe FIDI driver]

	== FAQ ==		== FAQ ==

2014-05-23T01:20:36Z

How to buy

← Older revision		Revision as of 01:20, 23 May 2014
Line 102:		Line 102:
	== How to buy ==		== How to buy ==

	Click here to buy		Click here to buy [http://www.geeetech.com/lilypad-xbee-p-822.html Lilypad Xbee]

2014-05-22T06:03:35Z

Instruction:

2014-05-22T06:03:07Z

Instruction:

← Older revision		Revision as of 06:03, 22 May 2014
Line 39:		Line 39:
	void setup()		void setup()
	{		{
	Serial.begin(9600);//initialize serial port to send and receive at 9600 baud		Serial.begin(9600);//initialize serial port to send and receive at 9600 baud
	pinMode(ledPin,OUTPUT);//set this pin sa output		pinMode(ledPin,OUTPUT);//set this pin sa output
	}		}
	void loop()		void loop()
	{		{
	blink();		blink();
	}		}

	void serialEvent(void)		void serialEvent(void)
	{		{
	while(Serial.available())		while(Serial.available())
	{		{
	char ch=Serial.read();		char ch=Serial.read();
	//is this an ascii digit between 0 and 9?the data's type received from		//is this an ascii digit between 0 and 9?the data's type received from
	//Mobile phone bluetooth serial port is String tpye		//Mobile phone bluetooth serial port is String tpye
	if(isDigit(ch))		if(isDigit(ch))
	{		{
	blinkread=ch-'0';//ascii value converted to numeric value		blinkread=ch-'0';//ascii value converted to numeric value
	blinkread*=100; //actual rate is 100ms times received digit		blinkread*=100; //actual rate is 100ms times received digit
	}		}
	}		}
	}		}
	//blink the LED with the on and off times determined by blinkrate		//blink the LED with the on and off times determined by blinkrate
	void blink()		void blink()
	{		{
	digitalWrite(ledPin,HIGH);		digitalWrite(ledPin,HIGH);
	delay(blinkread);		delay(blinkread);
	digitalWrite(ledPin,LOW);		digitalWrite(ledPin,LOW);
	delay(blinkread);		delay(blinkread);
	}		}

	== Notes ==		== Notes ==

2014-05-22T06:01:54Z

Instruction:

← Older revision		Revision as of 06:01, 22 May 2014
Line 35:		Line 35:


	const int ledPin=13;//pin the led is connected to		const int ledPin=13;//pin the led is connected to
	int blinkread=0; //blink rate stored in this variable		int blinkread=0; //blink rate stored in this variable
	void setup()		void setup()
	{		{
	Serial.begin(9600);//initialize serial port to send and receive at 9600 baud		Serial.begin(9600);//initialize serial port to send and receive at 9600 baud
	pinMode(ledPin,OUTPUT);//set this pin sa output		pinMode(ledPin,OUTPUT);//set this pin sa output

2014-05-22T06:01:19Z

FAQ

← Older revision		Revision as of 06:01, 22 May 2014
Line 14:		Line 14:
	== FAQ ==		== FAQ ==

	Q1:How to judge the LilyPad Bee connect to power exactly?		Q1:How to judge the LilyPad Bee connect to power exactly?
	A:When the LilyPad Bee connect to power exactly , the “PWR” LED is on and “STATE” LED is flashing;		A:When the LilyPad Bee connect to power exactly , the “PWR” LED is on and “STATE” LED is flashing;
	Q:How to judge the LilyPad Bee connect to mobile Bluetooth software?		Q:How to judge the LilyPad Bee connect to mobile Bluetooth software?
	A:When the LilyPad Bee connect to mobile Bluetooth software ,the “STATE” LED is on not flash.		A:When the LilyPad Bee connect to mobile Bluetooth software ,the “STATE” LED is on not flash.

	== Example code ==		== Example code ==

2014-05-22T06:00:23Z

Introduction

2014-05-22T04:27:55Z

instruction:

← Older revision		Revision as of 04:27, 22 May 2014
Line 22:		Line 22:


	=== ~~instruction~~: ===		=== Instruction: ===

	The code tested successfullly by Arduino 1.0 IDE		The code tested successfullly by Arduino 1.0 IDE

2014-05-22T04:27:36Z

Example code

← Older revision		Revision as of 04:27, 22 May 2014
Line 22:		Line 22:


	* instruction:The code tested successfullly by Arduino 1.0 IDE		=== instruction: ===
			The code tested successfullly by Arduino 1.0 IDE

	* BlueTooth module-------Aduino Board		* BlueTooth module-------Aduino Board
	* Tx0 -------Rx		* Tx0 -------Rx

2014-05-22T04:26:38Z

Example code

← Older revision		Revision as of 04:26, 22 May 2014
Line 21:		Line 21:
	== Example code ==		== Example code ==

	/*
	* instruction:The code tested successfullly by Arduino 1.0 IDE		* instruction:The code tested successfullly by Arduino 1.0 IDE
	* BlueTooth module-------Aduino Board		* BlueTooth module-------Aduino Board
Line 28:		Line 28:
	* GND -------GND		* GND -------GND
	* 3.3V(+) -------3.3V(5V)		* 3.3V(+) -------3.3V(5V)
	*/