Geeetech prusa i3 pro C building instruction - Revision history

Admin: /* Mount the control board on the left side panel */

2015-07-07T10:03:07Z

Mount the control board on the left side panel

← Older revision		Revision as of 10:03, 7 July 2015
Line 749:		Line 749:

	Before you start wiring, please take a look at the wiring schematics.		Before you start wiring, please take a look at the wiring schematics.

	[[File:GT2560 wiring.jpg\|900px\|]]		[[File:GT2560 wiring.jpg\|900px\|]]

2015-06-30T09:54:46Z

Mount the control board on the left side panel

← Older revision		Revision as of 09:54, 30 June 2015
Line 749:		Line 749:

	Before you start wiring, please take a look at the wiring schematics.		Before you start wiring, please take a look at the wiring schematics.
			[[File:GT2560 wiring.jpg\|900px\|]]

	~~[[GT2560 wiring.jpg\|900px\|]]~~

	<font color=red> There is one thing you need to note that the extruder number in this picture is 1 and 2, but in the following steps, I referred them as 0 and 1 correspondingly.</font>		<font color=red> There is one thing you need to note that the extruder number in this picture is 1 and 2, but in the following steps, I referred them as 0 and 1 correspondingly.</font>

2015-06-30T09:52:06Z

Mount the control board on the left side panel

← Older revision		Revision as of 09:52, 30 June 2015
Line 750:		Line 750:
	Before you start wiring, please take a look at the wiring schematics.		Before you start wiring, please take a look at the wiring schematics.

	[[~~File:2-1~~.jpg\|900px\|]]		[[GT2560 wiring.jpg\|900px\|]]

	<font color=red> There is one thing you need to note that the extruder number in this picture is 1 and 2, but in the following steps, I referred them as 0 and 1 correspondingly.</font>		<font color=red> There is one thing you need to note that the extruder number in this picture is 1 and 2, but in the following steps, I referred them as 0 and 1 correspondingly.</font>

2015-06-08T03:32:52Z

Step4

← Older revision		Revision as of 03:32, 8 June 2015
Line 844:		Line 844:

	[[File:Heating wire of extruder 1.jpg\|500px\|]]		[[File:Heating wire of extruder 1.jpg\|500px\|]]


	===Step5===		===Step5===

2015-05-28T02:45:33Z

← Older revision	Revision as of 02:45, 28 May 2015
(No difference)

2015-05-28T02:33:08Z

Step2

← Older revision		Revision as of 02:33, 28 May 2015
Line 765:		Line 765:

	[[File:Stack A4988.jpg\|500px\|]]		[[File:Stack A4988.jpg\|500px\|]]
	~~If you are using DRV8825 instead of A4988, The correct connections are as follow:~~

			If you are using DRV8825 instead of A4988, The correct connections are as follow:<br>
	[[File:3-3.jpg\|500px\|]]		[[File:3-3.jpg\|500px\|]]

2015-05-28T02:32:37Z

Step2

← Older revision		Revision as of 02:32, 28 May 2015
Line 765:		Line 765:

	[[File:Stack A4988.jpg\|500px\|]]		[[File:Stack A4988.jpg\|500px\|]]
			If you are using DRV8825 instead of A4988, The correct connections are as follow:

			[[File:3-3.jpg\|500px\|]]

	===Step3===		===Step3===

2015-05-06T07:12:58Z

Step2

← Older revision		Revision as of 07:12, 6 May 2015
Line 762:		Line 762:

	===Step2===		===Step2===
	Plug the 5 A4988 into the stepper motor driver slot. Mind the directions of A4988.		Plug the 5 A4988 into the stepper motor driver slot. Mind the directions of A4988.<font color="red"> (It is recommended wear static gloves when plugging A4988)</font><br>

	[[File:Stack A4988.jpg\|500px\|]]		[[File:Stack A4988.jpg\|500px\|]]

2015-05-05T04:00:42Z

Step6

← Older revision		Revision as of 04:00, 5 May 2015
Line 863:		Line 863:
	<font color=red>* There is no “+” and “-“for endstop</font>		<font color=red>* There is no “+” and “-“for endstop</font>

	1) Connect wires for endstop of X-axis at X-~~max~~.		1) Connect wires for endstop of X-axis at X-MIN.

	[[File:X endstop.jpg\|500px\|]]		[[File:X endstop.jpg\|500px\|]]

	2) Connect wires for endstop of Y-axis at Y-~~max~~.		2) Connect wires for endstop of Y-axis at Y-MIN.

	[[File:Y endstop.jpg\|500px\|]]		[[File:Y endstop.jpg\|500px\|]]

	3) Connect wires for endstop of Z-axis at Z-~~max~~.		3) Connect wires for endstop of Z-axis at Z-MIN.

	[[File:Z-endstop.jpg\|500px\|]]		[[File:Z-endstop.jpg\|500px\|]]


	===Step7===		===Step7===

2015-05-05T02:03:21Z

Mount the Y motor

← Older revision		Revision as of 02:03, 5 May 2015
Line 157:		Line 157:
	Step2. Insert the motor block into the slot; you may need to use a little strength to do this. But be careful in case the Acrylic broke down. Then screw the motor on the block plate with 3 M3 x 12 screws and fix the block plate with 2 M3 x 16 screws and M3 square nut.		Step2. Insert the motor block into the slot; you may need to use a little strength to do this. But be careful in case the Acrylic broke down. Then screw the motor on the block plate with 3 M3 x 12 screws and fix the block plate with 2 M3 x 16 screws and M3 square nut.

	[[File:~~Fix motor~~.~~png~~\|500px]]		[[File:Ymotor.jpg\|500px]]

	==Build the printing platform==		==Build the printing platform==