Geeetech Delta Rostock mini - Revision history

Admin at 06:46, 5 May 2015

2015-05-05T06:46:06Z

@@ Line 368: / Line 368: @@
 . Now slide the extruder back to check the tension of the bottom belts in front of the y carriages. Again, these belts should be not too tight and not too loose. Using a 2.5 mm hex driver on the screws on the front of the y carriages, adjust the belts so that they are of roughly equal tension.
 . If the belts are still not moving smoothly, there may be a problem with the pulley alignment on the back horizontal rod. Using your 1.5 mm hex driver, loosen the screw on the pulleys so that you can move them into alignment, then tighten to hold them in place. This step can take some trial and error until you get everything properly aligned.
 ==FAQs & SOLUTIONs==

Admin: /* Install Software */

2015-01-30T05:51:50Z

Install Software

← Older revision		Revision as of 05:51, 30 January 2015
Line 218:		Line 218:
	To install all required software by Delta Rostock mini, please follow the steps provided below.		To install all required software by Delta Rostock mini, please follow the steps provided below.

	1) Download and install: [http://www.geeetech.com/~~Documents~~/~~RepetierGEtechSetup~~.~~exe~~ RepetierGEtechSetup.exe]		1) Download and install: [http://www.geeetech.com/wiki/images/9/96/SetupRepetierHostGEEEtech_0_90D_2.zip RepetierGEtechSetup.exe]

	step 1,start the installer,choose the display language.		step 1,start the installer,choose the display language.

Admin: /* FAQs & SOLUTIONs */

2015-01-08T03:20:33Z

FAQs & SOLUTIONs

← Older revision		Revision as of 03:20, 8 January 2015
Line 376:		Line 376:

	3.[http://www.geeetech.com/wiki/index.php/FAQs_OF_3D_printing FAQs OF 3D printing]		3.[http://www.geeetech.com/wiki/index.php/FAQs_OF_3D_printing FAQs OF 3D printing]

			==Where to get==

			1,[http://www.geeetech.com/unassembledfull-kit-for-geeetech-delta-rostock-mini-p-835.html geeetech official oline store]

Admin: /* detailes 0f me creator */

2015-01-08T02:08:48Z

detailes 0f me creator

← Older revision		Revision as of 02:08, 8 January 2015
Line 369:		Line 369:
	16. If the belts are still not moving smoothly, there may be a problem with the pulley alignment on the back horizontal rod. Using your 1.5 mm hex driver, loosen the screw on the pulleys so that you can move them into alignment, then tighten to hold them in place. This step can take some trial and error until you get everything properly aligned.		16. If the belts are still not moving smoothly, there may be a problem with the pulley alignment on the back horizontal rod. Using your 1.5 mm hex driver, loosen the screw on the pulleys so that you can move them into alignment, then tighten to hold them in place. This step can take some trial and error until you get everything properly aligned.

	==~~detailes 0f me creator~~==		==FAQs & SOLUTIONs==
	~~<gallery>~~
	~~Image~~:~~IMG 6640~~.~~jpg\| Internally installed LED strips~~		1.[http://www.geeetech.com/wiki/index.php/Fixing_Extruder_Jams_and_Flow_Problems Fixing Extruder Jams and Flow Problems]
	~~Image~~:~~Details of me ceator~~.~~jpg\| heatbed~~
	~~Image:Belts of x,y axis~~.~~jpg\| Belts of x,y axis~~		2.[http://www.geeetech.com/wiki/index.php/How_to_unblock_a_nozzle How to unblock a nozzle]
	~~Image~~:~~Belt of z axis~~.~~jpg\| Belt of z axis~~
	~~Image:IMG 6661~~.~~jpg\| MK8 extruder~~		3.[http://www.geeetech.com/wiki/index.php/FAQs_OF_3D_printing FAQs OF 3D printing]
	~~Image:IMG 6682~~.~~jpg\| Print carriage~~
	</~~gallery>~~

Admin: /* Belt Tensioning */

2015-01-08T01:48:05Z

Belt Tensioning

← Older revision		Revision as of 01:48, 8 January 2015
Line 326:		Line 326:
	==Belt Tensioning==		==Belt Tensioning==

	~~[[File:Belts of x,y axis.jpg\|300px\|]] [[File:Belt of z axis.jpg\|300px\|]]~~

	There are 3 belts to be adjusted on your Delta Rostock mini. These steps will guide you through adjusted them.		There are 3 belts to be adjusted on your Delta Rostock mini. These steps will guide you through adjusted them.
Line 369:		Line 368:
	15. Now slide the extruder back to check the tension of the bottom belts in front of the y carriages. Again, these belts should be not too tight and not too loose. Using a 2.5 mm hex driver on the screws on the front of the y carriages, adjust the belts so that they are of roughly equal tension.		15. Now slide the extruder back to check the tension of the bottom belts in front of the y carriages. Again, these belts should be not too tight and not too loose. Using a 2.5 mm hex driver on the screws on the front of the y carriages, adjust the belts so that they are of roughly equal tension.
	16. If the belts are still not moving smoothly, there may be a problem with the pulley alignment on the back horizontal rod. Using your 1.5 mm hex driver, loosen the screw on the pulleys so that you can move them into alignment, then tighten to hold them in place. This step can take some trial and error until you get everything properly aligned.		16. If the belts are still not moving smoothly, there may be a problem with the pulley alignment on the back horizontal rod. Using your 1.5 mm hex driver, loosen the screw on the pulleys so that you can move them into alignment, then tighten to hold them in place. This step can take some trial and error until you get everything properly aligned.




	==detailes 0f me creator==		==detailes 0f me creator==

Admin: /* Leveling The Print Bed */

2015-01-08T01:39:54Z

Leveling The Print Bed

← Older revision		Revision as of 01:39, 8 January 2015
Line 307:		Line 307:
	==Leveling The Print Bed==		==Leveling The Print Bed==

	[[File:~~Me creator heatbed~~.jpg\|300px\|]]		[[File:Geeetech mini htbed 1.jpg\|300px\|]]

	Getting the bed level in relation to the X and Y axis is very important for getting prints to stick well and is one of the first steps you should do when receiving your Delta ~~Rostock mini~~. The first layer might have the right amount of squish in one area, but if another part of the bed is too low, that part of the print is more likely to come unstuck and begin to warp. The level is adjusted with the spring loaded screws, two at the front and one at the back. If you are using the standard kapton tape on the build platform and not a sheet of glass, you will need to poke holes in the tape in order to turn the leveling screws or print some thumbscrews and use a little super glue to screw them onto the bottom of the leveling screws. We suggest using the thumbscrew route so that you do not have to damage your kapton tape.		Getting the bed level in relation to the X and Y axis is very important for getting prints to stick well and is one of the first steps you should do when receiving your Delta . The first layer might have the right amount of squish in one area, but if another part of the bed is too low, that part of the print is more likely to come unstuck and begin to warp. The level is adjusted with the spring loaded screws, two at the front and one at the back. If you are using the standard kapton tape on the build platform and not a sheet of glass, you will need to poke holes in the tape in order to turn the leveling screws or print some thumbscrews and use a little super glue to screw them onto the bottom of the leveling screws. We suggest using the thumbscrew route so that you do not have to damage your kapton tape.

Admin: /* Leveling The Print Bed */

2015-01-08T01:36:23Z

Leveling The Print Bed

← Older revision		Revision as of 01:36, 8 January 2015
Line 301:		Line 301:

	[[File:ManualControl2.png]][[File:Screen-shot-2013-11-18-at-9.27.00-PM.png]]		[[File:ManualControl2.png]][[File:Screen-shot-2013-11-18-at-9.27.00-PM.png]]

			==Assembly==
			Here is a brif [http://www.geeetech.com/Documents/Rostock%20mini%20Build%20manual(1).pdf assembly manual] for you to refer, welcome to add a more detailed one.

	==Leveling The Print Bed==		==Leveling The Print Bed==

Admin: /* How To Connect */

2015-01-08T01:32:46Z

How To Connect

← Older revision		Revision as of 01:32, 8 January 2015
Line 273:		Line 273:
	[[File:1setting.png]]		[[File:1setting.png]]

	4,Select GEEEtech ~~MeCreator~~ in “Printer”		4,Select GEEEtech Rostock mini in “Printer”

	[[File:2choose printer.png]]		[[File:2choose printer.png]]
Line 281:		Line 281:
	[[File:3 CHOOSE COM.png]]		[[File:3 CHOOSE COM.png]]

	6. Hit "connect" in the upper left-hand corner, select GEEEtech ~~MeCreator~~. You should see the details of the connection in the console window in the bottom section of the screen.		6. Hit "connect" in the upper left-hand corner, select GEEEtech Rostock mini. You should see the details of the connection in the console window in the bottom section of the screen.

	[[File:4connection (1).png]]		[[File:4connection (1).png]]
Line 297:		Line 297:
	7. Once full heat has been achieved do a few quick tests.		7. Once full heat has been achieved do a few quick tests.
	Hit the X+/X- arrows to ensure that movement is possible.		Hit the X+/X- arrows to ensure that movement is possible.

	Hit the extrude button, with the down arrow, in the Extruder section to ensure extrusion is possible.		Hit the extrude button, with the down arrow, in the Extruder section to ensure extrusion is possible.

Admin at 01:30, 8 January 2015

2015-01-08T01:30:57Z

Show changes

Admin at 01:24, 8 January 2015

2015-01-08T01:24:23Z

Show changes