Building Instructions of Geeetech Prusa I3 M201 - Revision history

Admin: /* Step3. Connect wires for thermistor */

2015-12-03T04:05:54Z

Step3. Connect wires for thermistor

← Older revision		Revision as of 04:05, 3 December 2015
Line 1,077:		Line 1,077:
	[[File:27.GTM32 13.jpg\|500px]]		[[File:27.GTM32 13.jpg\|500px]]

	2)Connect wires for thermistor of hotend 1		2)Connect wires for thermistor of hotend 0

	[[File:~~2)thermistor of hotend 1~~.~~png~~\|500px]]		[[File:H0 TEMP.jpg\|500px]]

	==Step4. Connect wires for endstop==		==Step4. Connect wires for endstop==

Admin: /* Step2. Connect heating wires */

2015-12-03T04:01:25Z

Step2. Connect heating wires

← Older revision		Revision as of 04:01, 3 December 2015
Line 1,065:		Line 1,065:
	[[File:27.GTM32 10.jpg\|500px]]		[[File:27.GTM32 10.jpg\|500px]]

	2） Connect heating wires for hotend 1.		2） Connect heating wires for hotend 0.

	[[File:27.GTM32 11.jpg\|500px]]		[[File:27.GTM32 11.jpg\|500px]]

Admin: /* Assemble the front and back support of y axis */

2015-11-17T06:51:11Z

Assemble the front and back support of y axis

← Older revision		Revision as of 06:51, 17 November 2015
Line 70:		Line 70:
	Watch the [https://www.youtube.com/watch?v=KCKfAqoxRZg&list=PLODCkot3GrihN2yzDrAGAwSVQ-cbIUObs&index=1 Video] here.		Watch the [https://www.youtube.com/watch?v=KCKfAqoxRZg&list=PLODCkot3GrihN2yzDrAGAwSVQ-cbIUObs&index=1 Video] here.

	= Assemble the front and back support of y axis=		= Assemble the front and back support of Y axis=

	{\|class="wikitable"		{\|class="wikitable"

Admin: /* Unfold the box and check the package list */

2015-11-17T06:50:51Z

Unfold the box and check the package list

← Older revision		Revision as of 06:50, 17 November 2015
Line 41:		Line 41:
	* All the acrylic plate has been etched with part ID and the plate is covered with a sheet of kraft paper, you need to tear them off.		* All the acrylic plate has been etched with part ID and the plate is covered with a sheet of kraft paper, you need to tear them off.

	* The part ID is corresponding to the number labeled on the bag of every part. Some parts may not have label, you can refer to the pictures on the package list.~~</font>~~		* The part ID is corresponding to the number labeled on the bag of every part. Some parts may not have label, you can refer to the pictures on the package list.


	*Download the [http://www.geeetech.com/wiki/images/4/43/Building_Instructions_of_Geeetech_Prusa_I3_M201.pdf Building instruction here].		*Download the [http://www.geeetech.com/wiki/images/4/43/Building_Instructions_of_Geeetech_Prusa_I3_M201.pdf Building instruction here].

	For instruction videos, please go to our [https://www.youtube.com/playlist?list=PLODCkot3GrihN2yzDrAGAwSVQ-cbIUObs YouTube channel].		For instruction videos, please go to our [https://www.youtube.com/playlist?list=PLODCkot3GrihN2yzDrAGAwSVQ-cbIUObs YouTube channel].</font>

	=Assemble the threaded rods of Y axis=		=Assemble the threaded rods of Y axis=

Admin: /* Unfold the box and check the package list */

2015-11-17T06:50:32Z

Unfold the box and check the package list

← Older revision		Revision as of 06:50, 17 November 2015
Line 42:		Line 42:

	* The part ID is corresponding to the number labeled on the bag of every part. Some parts may not have label, you can refer to the pictures on the package list.</font>		* The part ID is corresponding to the number labeled on the bag of every part. Some parts may not have label, you can refer to the pictures on the package list.</font>


			*Download the [http://www.geeetech.com/wiki/images/4/43/Building_Instructions_of_Geeetech_Prusa_I3_M201.pdf Building instruction here].

			For instruction videos, please go to our [https://www.youtube.com/playlist?list=PLODCkot3GrihN2yzDrAGAwSVQ-cbIUObs YouTube channel].

	=Assemble the threaded rods of Y axis=		=Assemble the threaded rods of Y axis=

Admin: /* Mount the filament spool */

2015-11-17T06:48:05Z

Mount the filament spool

← Older revision		Revision as of 06:48, 17 November 2015
Line 1,196:		Line 1,196:
	Extruder is calibrated in the firmware with the correct steps per mm of filament.		Extruder is calibrated in the firmware with the correct steps per mm of filament.
	The point regarding the extruder step rate is vital. Slic3r expects that the machine will accurately produce a set amount of filament when told to do so. Too much will result in blobs and other imperfections in the print. Too little will result in gaps and poor inter-layer adhesion.		The point regarding the extruder step rate is vital. Slic3r expects that the machine will accurately produce a set amount of filament when told to do so. Too much will result in blobs and other imperfections in the print. Too little will result in gaps and poor inter-layer adhesion.

			=more=
			For more detailed information about prusa I3 M201, please visit [http://www.geeetech.com/wiki/index.php/Geeetech_Prusa_I3_M201 here]

			To buy prusa I3 M201,please go to our [http://www.geeetech.com/geeetech-prusa-i3-m201-3d-printer-diy-kit-p-965.html online store].

Admin: /* Mount the filament spool */

2015-11-17T06:42:56Z

Mount the filament spool

← Older revision		Revision as of 06:42, 17 November 2015
Line 1,167:		Line 1,167:
	\|<center>M3 x 16mm screw</center>\|\|<center>No.23</center>\|\|<center>6</center>		\|<center>M3 x 16mm screw</center>\|\|<center>No.23</center>\|\|<center>6</center>
	\|-		\|-
	\|<center>M3 Square nut</center>\|\|<center>No.16</center>\|\|<center>6</center>		\|<center>M3 Square nut</center>\|\|<center>No.17</center>\|\|<center>6</center>
	\|-		\|-
	\|<center>M3 washer</center>\|\|<center>No.7</center>\|\|<center>6</center>		\|<center>M3 washer</center>\|\|<center>No.7</center>\|\|<center>6</center>

Admin: /* Mount the Y endstop */

2015-11-17T06:42:10Z

Mount the Y endstop

← Older revision		Revision as of 06:42, 17 November 2015
Line 1,158:		Line 1,158:

	That is all for the wiring of GTM32.		That is all for the wiring of GTM32.

	~~= Mount the Y endstop=~~

	~~{\|class="wikitable"~~
	\|-
	~~!Required parts!!Part ID!!Required number~~
	\|-
	~~\|<center>M2.5 x 16mm screw</center>\|\|<center>No. 22</center>\|\|<center>2</center>~~
	\|-
	~~\|<center>M2.5 hex nut </center>\|\|<center> No. 11</center>\|\|<center>2</center>~~
	\|-
	~~\|<center>End stop</center>\|\|<center>No.54</center>\|\|<center>1</center>~~
	\|-
	\|}

	~~Mount the Y axis endstop on A12with M2.5 x 16mm screw and M2.5 hex nut~~

	~~[[File:Mount Y endstop.jpg]]~~

	=Mount the filament spool=		=Mount the filament spool=

Admin: /* Step5. Connect wires for Fan */

2015-11-17T06:40:44Z

Step5. Connect wires for Fan

← Older revision		Revision as of 06:40, 17 November 2015
Line 1,105:		Line 1,105:
	Black: -		Black: -

	1)Connect fan for control board at ~~FAN4~~.		1)Connect fan for control board at FAN3.

	[[File:27.GTM32 20.jpg\|500px]]		[[File:27.GTM32 20.jpg\|500px]]

	2)Connect fan for extruder 0 at ~~FAN1~~.		2)Connect fan for extruder 0 at FAN0.

	[[File:27.GTM32 21.jpg\|500px]]		[[File:27.GTM32 21.jpg\|500px]]
Line 1,117:		Line 1,117:
	[[File:27.GTM32 22.jpg\|500px]]		[[File:27.GTM32 22.jpg\|500px]]

	4)Connect fan for hotend at ~~FAN5~~.		4)Connect fan for hotend at FAN4.

	Note: for the fan of hotend, you will need the extension wire. Just connect the red and black connectors.		Note: for the fan of hotend, you will need the extension wire. Just connect the red and black connectors.

Admin: /* Wiring */

2015-11-17T06:39:11Z

Wiring

← Older revision		Revision as of 06:39, 17 November 2015
Line 1,017:		Line 1,017:
	[[File:GTM32 wiring.jpg\|1000px]]		[[File:GTM32 wiring.jpg\|1000px]]

	~~'''~~Step1. Connect wires for motors~~.'''~~		==Step1. Connect wires for motors==

	[[File:27.Wiring1.jpg\|700px]]		[[File:27.Wiring1.jpg\|700px]]
Line 1,043:		Line 1,043:
	[[File:27.Wiring6.jpg\|500px]]		[[File:27.Wiring6.jpg\|500px]]

	~~'''~~Step2. Connect heating wires~~.'''~~		==Step2. Connect heating wires==

	[[File:27.GTM32 7.jpg\|700px]]		[[File:27.GTM32 7.jpg\|700px]]
Line 1,065:		Line 1,065:
	[[File:27.GTM32 11.jpg\|500px]]		[[File:27.GTM32 11.jpg\|500px]]

	~~'''~~Step3. Connect wires for thermistor~~.'''~~		==Step3. Connect wires for thermistor==

	[[File:27.GTM32 12.jpg\|700px]]		[[File:27.GTM32 12.jpg\|700px]]
Line 1,077:		Line 1,077:
	[[File:2)thermistor of hotend 1.png\|500px]]		[[File:2)thermistor of hotend 1.png\|500px]]

	~~'''~~Step4. Connect wires for endstop~~.'''~~		==Step4. Connect wires for endstop==

	[[File:27.GTM32 15.jpg\|700px]]		[[File:27.GTM32 15.jpg\|700px]]
Line 1,095:		Line 1,095:
	[[File:27.GTM32 18.jpg\|500px]]		[[File:27.GTM32 18.jpg\|500px]]

	~~'''~~Step5. Connect wires for Fan~~.'''~~		==Step5. Connect wires for Fan==

	[[File:27.GTM32 19.jpg\|700px]]		[[File:27.GTM32 19.jpg\|700px]]
Line 1,123:		Line 1,123:
	[[File:27.GTM32 23.jpg\|500px]]		[[File:27.GTM32 23.jpg\|500px]]

	~~'''~~Step6. Connect wires for LCD panel~~.'''~~		==Step6. Connect wires for LCD panel==

	There are two cables, one is for LCD encoder, the other is for SD card.		There are two cables, one is for LCD encoder, the other is for SD card.
Line 1,137:		Line 1,137:
	[[File:27.GTM32 24.jpg\|500px]]		[[File:27.GTM32 24.jpg\|500px]]

	~~'''~~Step7. Connect wires for power input~~.'''~~		==Step7. Connect wires for power input==

	[[File:27.GTM32 26.jpg\|500px]]		[[File:27.GTM32 26.jpg\|500px]]

	~~'''~~Step8. Connect the wires to the PSU~~.'''~~		==Step8. Connect the wires to the PSU==

	<font color=red>		<font color=red>