Brainwave - Revision history

Admin: /* File Burning */

2014-08-21T09:14:33Z

File Burning

← Older revision		Revision as of 09:14, 21 August 2014
Line 83:		Line 83:
	[[File:Pfb2.jpg\|500px\|]]		[[File:Pfb2.jpg\|500px\|]]

	Click the ~~“check ( )” button~~ to check if it is right and then click ~~the “ ” button~~ to upload firmware, as shown below.		Click the [[File:button1.jpg]]to check if it is right and then click [[File:button2.jpg]]to upload firmware, as shown below.

	[[File:Rumba 11.jpg\|500px\|]]		[[File:Rumba 11.jpg\|500px\|]]
Line 138:		Line 138:

	[[File:Rh3.jpg\|500px\|]]		[[File:Rh3.jpg\|500px\|]]



	==firmware==		==firmware==

2014-08-21T09:13:14Z

Interface Layout

← Older revision		Revision as of 09:13, 21 August 2014
Line 50:		Line 50:
	==Interfaces==		==Interfaces==
	===Interface Layout===		===Interface Layout===

			[[File:Brainwaveinterface .jpg\|500px\|]]

	===Interface specifications===		===Interface specifications===

2014-08-21T09:12:37Z

Overview and Hardware Resource

← Older revision		Revision as of 09:12, 21 August 2014
Line 30:		Line 30:
	===Overview and Hardware Resource===		===Overview and Hardware Resource===

			[[File:Brainwaveoverview.jpg\|500px\|]]

	size：60mm*79mm		size：60mm*79mm

	weight：81g		weight：81g


	===Software Resources===		===Software Resources===

2014-08-21T09:12:06Z

Interface Layout

← Older revision		Revision as of 09:12, 21 August 2014
Line 50:		Line 50:
	==Interfaces==		==Interfaces==
	===Interface Layout===		===Interface Layout===

	~~[[File:Brainwaveoverview.jpg\|500px\|]]~~

	===Interface specifications===		===Interface specifications===

2014-08-21T09:10:21Z

Interface Layout

← Older revision		Revision as of 09:10, 21 August 2014
Line 50:		Line 50:
	==Interfaces==		==Interfaces==
	===Interface Layout===		===Interface Layout===

			[[File:Brainwaveoverview.jpg\|500px\|]]

	===Interface specifications===		===Interface specifications===
	2 ADC interfaces for thermometry: one for extruder and another for hotbed.		2 ADC interfaces for thermometry: one for extruder and another for hotbed.

2014-08-21T09:03:49Z

Software Resources

2014-08-21T08:41:38Z

Introduction

← Older revision		Revision as of 08:41, 21 August 2014
Line 1:		Line 1:
	==Introduction==		==Introduction==

			[[File:BRAINWAVE.jpg\|500px\|]]

			Brainwave, derived from sanguinololu, is control board for reprap 3D printer with low cost and high capacity-price ratio in that it is powerful to drive a printer of single-screw extruder by providing only the minimum required components. Such as a printer with single extruder and 2 Z axis or the delta style printer.

			'''Features:'''

			*12v power input

			*standard micro USB connector

			*The entire interfaces are at the edge of the board, making it possible to fit vertical or right-angle connectors.

			*Adopt Atmel AT90USB646 microcontroller, with USB- RS232.

			*The steps of stepper motor can be divided into 1, 2, 16, and 32. The maximum power output can reach to 800MA

			*2 connectors for Z axis

			*Optional motor power output of each axis

			*Heated bed supports separate power input from the logic part (up to 24V 15A)

			*Integrated heater/thermistor/stepper connector for E channel

			*controllable fan


			===Overview and Hardware Resource===


			size：60mm*79mm

			weight：81g


			===Software Resources===
			Compiling environment: Arduino IDE http://www.geeetech.com/wiki/images/3/36/Arduino-1.0.5-r2-windows.zip

			Firmware: Marlin http://www.geeetech.com/wiki/images/3/39/Marlin-Marlin_v1.zip

			Pc software:

			printrun http://www.geeetech.com/wiki/images/e/e1/Printrun-Win-Slic3r-10Mar2014.zip

			Repetier-Host http://www.geeetech.com/wiki/images/3/36/SetupRepetierHost_1_00.zip

2014-08-21T08:32:01Z

Created page with "==Introduction=="

New page

==Introduction==