Arduino Digital Vibration Sensor module - Revision history

Admin: /* introduction */

2012-05-14T10:01:11Z

introduction

← Older revision		Revision as of 10:01, 14 May 2012
Line 1:		Line 1:
	==~~introduction~~==		==Introduction==
	[[File:Vibration sensor.jpg]]		[[File:Vibration sensor.jpg]]

Admin at 09:54, 14 May 2012

2012-05-14T09:54:33Z

← Older revision		Revision as of 09:54, 14 May 2012
Line 13:		Line 13:
	On-Time: 0.1ms <br>		On-Time: 0.1ms <br>
	Open circuit resistance: 10Mohm<br>		Open circuit resistance: 10Mohm<br>

			==Pin definition==
			[[File:Vibration 1.jpg]]

	==Usage==		==Usage==

Admin at 09:53, 14 May 2012

2012-05-14T09:53:20Z

← Older revision		Revision as of 09:53, 14 May 2012
Line 5:		Line 5:

	==Product Performance: ==		==Product Performance: ==
	The conductive pin will make an instant turn-on (ON) state when touched by the outside force to achieve the proper vibration force, or an appropriate speed from the (partial) energy.		*The conductive pin will make an instant turn-on (ON) state when touched by the outside force to achieve the proper vibration force, or an appropriate speed from the (partial) energy.
	No direction, any angle may burst.		*No direction, any angle may burst.
	The switch is suitable for small-current circuit (secondary circuit) or (IC) of the trigger.		*The switch is suitable for small-current circuit (secondary circuit) or (IC) of the trigger.
	At room temperature and normal use the next switch service life is up to 10 million times (times/1sec).		*At room temperature and normal use the next switch service life is up to 10 million times (times/1sec).

	==Specification==		==Specification==
	On-Time: 0.1ms		On-Time: 0.1ms <br>
	Open circuit resistance: 10Mohm		Open circuit resistance: 10Mohm<br>

	==Usage==		==Usage==
Line 44:		Line 44:
	}		}
	==How to buy it==		==How to buy it==
	Click here to buy [vibration sensor]		Click here to buy [http://www.geeetech.com/arduino-digital-vibration-sensor-module-shield-p-386.html vibration sensor]

Admin: Created page with "==introduction== File:Vibration sensor.jpg The Arduino vibration sensor module is based on vibration switch component which can detect the weak vibration signals. The sen..."

2012-05-14T09:52:04Z

Created page with "==introduction== File:Vibration sensor.jpg The Arduino vibration sensor module is based on vibration switch component which can detect the weak vibration signals. The sen..."

New page

==introduction==
[[File:Vibration sensor.jpg]]

The Arduino vibration sensor module is based on vibration switch component which can detect the weak vibration signals. The sensor can work for vibration-related modules.

==Product Performance: ==
The conductive pin will make an instant turn-on (ON) state when touched by the outside force to achieve the proper vibration force, or an appropriate speed from the (partial) energy.
No direction, any angle may burst.
The switch is suitable for small-current circuit (secondary circuit) or (IC) of the trigger.
At room temperature and normal use the next switch service life is up to 10 million times (times/1sec).

==Specification==
On-Time: 0.1ms
Open circuit resistance: 10Mohm

==Usage==
[[File:Vibration wiring.jpg|500px]]

VCC - 5V
GND - GND
S - Digital pin3

==Example code==
int ledPin = 13; // Connect LED to pin 13
int switcher = 3; // Connect Tilt sensor to Pin3
void setup()
{
pinMode(ledPin, OUTPUT); // Set digital pin 13 to output mode
pinMode(switcher, INPUT); // Set digital pin 3 to input mode
}
void loop()
{

if(digitalRead(switcher)==HIGH) //Read sensor value
{
digitalWrite(ledPin, HIGH); // Turn on LED when the sensor is tilted
delay(300);
}
else
{
digitalWrite(ledPin, LOW); // Turn off LED when the sensor is not triggered
}
}
==How to buy it==
Click here to buy [vibration sensor]