Arduino Bluetooth shield - Revision history

Admin: /* How to buy */

2013-01-08T09:21:48Z

How to buy

← Older revision		Revision as of 09:21, 8 January 2013
Line 74:		Line 74:

	==How to buy==		==How to buy==
	Click here to buy [Arduino Bluetooth shield]		Click here to buy [http://www.geeetech.com/stackable-bluetooth-shield-for-iduinoarduino-p-618.html Arduino Bluetooth shield]

Admin: /* Specifications: */

2013-01-04T08:02:45Z

Specifications:

← Older revision		Revision as of 08:02, 4 January 2013
Line 14:		Line 14:
	*USB protocol: USB v1.1/2.0		*USB protocol: USB v1.1/2.0
	*Frequency: 2.4GHz ISM band		*Frequency: 2.4GHz ISM band
	*Modulation: GFSK (Gaussian Frequency		*Modulation: GFSK (Gaussian Frequency)
	*Default Baud rate: 9600, Data bits: 8, Stop bit: 1, Parity: No parity		*Default Baud rate: 9600, Data bits: 8, Stop bit: 1, Parity: No parity
	*A full set of configuration commands		*A full set of configuration commands

Admin: /* Hardware Diagram */

2013-01-04T08:00:19Z

Hardware Diagram

← Older revision		Revision as of 08:00, 4 January 2013
Line 23:		Line 23:
	[[File:BT-1.jpg\|500px]]		[[File:BT-1.jpg\|500px]]

	'''S1''':Function button, This button is multi-function button include the function memory clearing (short press) which means deleting the address of the bluetooth module connected last time.Another function is to restore the default configuration(long press over 3s).		'''S1''':Function button, This button is a multi-function button include the function memory clearing (short press) which means deleting the address of the bluetooth module connected last time.Another function is to restore the default configuration(long press over 3s).

	'''S2''': The switch S2 is for hardware/software selection for master or slave mode. When the switch S2 is toggled to "HW" side indicate that you can set the module to either master or slave mode by switch S3. When the switch S2 is toggled to "SW" side means the master/slave mode is only decided by AT command "AT+role0/1"		'''S2''': The switch S2 is for hardware/software selection for master or slave mode. When the switch S2 is toggled to "HW" side indicate that you can set the module to either master or slave mode by switch S3. When the switch S2 is toggled to "SW" side means the master/slave mode is only decided by AT command "AT+role0/1"

Admin at 07:59, 4 January 2013

2013-01-04T07:59:50Z

← Older revision		Revision as of 07:59, 4 January 2013
Line 23:		Line 23:
	[[File:BT-1.jpg\|500px]]		[[File:BT-1.jpg\|500px]]

	S1:Function button, This button is multi-function button include the function memory clearing (short press) which means deleting the address of the bluetooth module connected last time.Another function is to restore the default configuration(long press over 3s).		'''S1''':Function button, This button is multi-function button include the function memory clearing (short press) which means deleting the address of the bluetooth module connected last time.Another function is to restore the default configuration(long press over 3s).

	S2: The switch S2 is for hardware/software selection for master or slave mode. When the switch S2 is toggled to "HW" side indicate that you can set the module to either master or slave mode by switch S3. When the switch S2 is toggled to "SW" side means the master/slave mode is only decided by AT command "AT+role0/1"		'''S2''': The switch S2 is for hardware/software selection for master or slave mode. When the switch S2 is toggled to "HW" side indicate that you can set the module to either master or slave mode by switch S3. When the switch S2 is toggled to "SW" side means the master/slave mode is only decided by AT command "AT+role0/1"

	S3: The switch S3 is for master/slave selection only if the S2 is toggled to "HW" side.		'''S3''': The switch S3 is for master/slave selection only if the S2 is toggled to "HW" side.

	===Selectable UART connection===		===Selectable UART connection===

Admin: /* Hardware Diagram */

2013-01-04T07:58:17Z

Hardware Diagram

← Older revision		Revision as of 07:58, 4 January 2013
Line 23:		Line 23:
	[[File:BT-1.jpg\|500px]]		[[File:BT-1.jpg\|500px]]

	S1:Function button, This button is multi-function button include the function memory clearing (short press) which means deleting the address of the bluetooth module connected last time ~~and the~~ function ~~restoring~~ the default configuration(long press over 3s).		S1:Function button, This button is multi-function button include the function memory clearing (short press) which means deleting the address of the bluetooth module connected last time.Another function is to restore the default configuration(long press over 3s).

	S2: The switch S2 is for hardware/software selection for master or slave mode. When the switch S2 is toggled to "HW" side indicate that you can set the module to either master or slave mode by switch S3. When the switch S2 is toggled to "SW" side means the master/slave mode is only decided by AT command "AT+role0/1"		S2: The switch S2 is for hardware/software selection for master or slave mode. When the switch S2 is toggled to "HW" side indicate that you can set the module to either master or slave mode by switch S3. When the switch S2 is toggled to "SW" side means the master/slave mode is only decided by AT command "AT+role0/1"

Admin: /* Hardware Specification */

2013-01-04T07:56:03Z

Hardware Specification

← Older revision		Revision as of 07:56, 4 January 2013
Line 42:		Line 42:
	[[File:BT-4.jpg\|500px]]		[[File:BT-4.jpg\|500px]]

	===State ~~Instructions~~ LED===		===State Indication LED===
	[[File:BT LED.jpg\|500px]]		[[File:BT LED.jpg\|500px]]

Admin at 07:55, 4 January 2013

2013-01-04T07:55:04Z

← Older revision		Revision as of 07:55, 4 January 2013
Line 23:		Line 23:
	[[File:BT-1.jpg\|500px]]		[[File:BT-1.jpg\|500px]]

	S1:Function button, This button is multi-function button include the function memory clearing (short press) which means ~~delete~~ the address of the bluetooth module connected last time and the function restoring the default configuration.		S1:Function button, This button is multi-function button include the function memory clearing (short press) which means deleting the address of the bluetooth module connected last time and the function restoring the default configuration(long press over 3s).

	S2: The switch S2 is for hardware/software selection for master or slave mode. When the switch S2 is toggled to "HW" side indicate that you can set the module to either master or slave mode by switch S3. When the switch S2 is toggled to "SW" side means the master/slave mode is only decided by AT command "AT+~~role<0~~/1>"		S2: The switch S2 is for hardware/software selection for master or slave mode. When the switch S2 is toggled to "HW" side indicate that you can set the module to either master or slave mode by switch S3. When the switch S2 is toggled to "SW" side means the master/slave mode is only decided by AT command "AT+role0/1"

	S3: The switch S3 is for master/slave selection only if the S2 is toggled to "HW" side.		S3: The switch S3 is for master/slave selection only if the S2 is toggled to "HW" side.

Admin: /* introduction */

2013-01-04T07:44:25Z

introduction

← Older revision		Revision as of 07:44, 4 January 2013
Line 2:		Line 2:
	[[File:BT-0.jpg\|400px]]		[[File:BT-0.jpg\|400px]]

	The Bluetooth Shield integrates a Serial Bluetooth module. It can be easily used with Arduino for transparent wireless serial connection setup. You can choose two pins from Arduino D0 to D7 as Software Serial Ports to communicate with Bluetooth Shield (D0 and D1 is Hardware Serial Port).		The Bluetooth Shield integrates a Serial Bluetooth module BLK-MD-BC04-B. It can be easily used with Arduino for transparent wireless serial connection setup. You can choose two pins from Arduino D0 to D7 as Software Serial Ports to communicate with Bluetooth Shield (D0 and D1 is Hardware Serial Port).

	;Note: The Shield may not be compatible with some Bluetooth capable devices, like Apple devices with special profile on Bluetooth function		;Note: The Shield may not be compatible with some Bluetooth capable devices, like Apple devices with special profile on Bluetooth function

Admin: /* Steps */

2013-01-04T07:34:39Z

Steps

← Older revision		Revision as of 07:34, 4 January 2013
Line 64:		Line 64:

	5.Set the switch "S1" on both shield to "HW" side, and set the switch "S2" to "SLAVE" on one shield and another to "MASTER" side.		5.Set the switch "S1" on both shield to "HW" side, and set the switch "S2" to "SLAVE" on one shield and another to "MASTER" side.

	6.The State LED always being on indicate that the two shield are connected.		6.The State LED always being on indicate that the two shield are connected.

	7.The connection is successful now, and you can type characters on the Serial monitor and send to each.		7.The connection is successful now, and you can type characters on the Serial monitor and send to each.

Admin: /* Steps */

2013-01-04T07:34:13Z

Steps

← Older revision		Revision as of 07:34, 4 January 2013
Line 66:		Line 66:
	6.The State LED always being on indicate that the two shield are connected.		6.The State LED always being on indicate that the two shield are connected.
	7.The connection is successful now, and you can type characters on the Serial monitor and send to each.		7.The connection is successful now, and you can type characters on the Serial monitor and send to each.
	~~[[File:BT-6.jpg]]~~

	[[File:BT-7.jpg]]		[[File:BT-6.jpg]] [[File:BT-7.jpg]]

	==Document==		==Document==