3D Touch - Revision history

Admin at 09:44, 4 March 2025

2025-03-04T09:44:03Z

← Older revision		Revision as of 09:44, 4 March 2025
Line 39:		Line 39:

	(1). Check whether the direction of the power cord is plugged in correctly, and the line sequence of the machine should be consistent with 3DTOUCH		(1). Check whether the direction of the power cord is plugged in correctly, and the line sequence of the machine should be consistent with 3DTOUCH

			[[File:New_3D Touch_1.png]]

	(2). Whether the power cord is disconnected		(2). Whether the power cord is disconnected

	(3). Whether the terminal block is plugged correctly		(3). Whether the terminal block is plugged correctly

	~~[[File:New_3D Touch_1.png]]~~

	[[File:New_3D Touch_2.png]]		[[File:New_3D Touch_2.png]]
Line 54:		Line 54:

	(1). Check whether the fastening bolts are locked in place, and adjust the fastening bolts up and down appropriately		(1). Check whether the fastening bolts are locked in place, and adjust the fastening bolts up and down appropriately

			[[File:New_3D Touch_3.png]]

	(2). When powering on, the probe should jump up and down, and finally retract, and the probe will be smoothly discharged		(2). When powering on, the probe should jump up and down, and finally retract, and the probe will be smoothly discharged

	~~(3). Check whether the coil resistance is correct and cannot be broken~~

	~~[[File:New_3D Touch_3.png]]~~

	[[File:New_3D Touch_4.png]]		[[File:New_3D Touch_4.png]]

			[[File:New_3D Touch_5.png]]

	~~[[File:New_3D Touch_5~~.~~png]]~~		(3). Check whether the coil resistance is correct and cannot be broken

	[[File:New_3D Touch_6.png]]		[[File:New_3D Touch_6.png]]

Admin at 09:41, 4 March 2025

2025-03-04T09:41:36Z

← Older revision		Revision as of 09:41, 4 March 2025
Line 44:		Line 44:
	(3). Whether the terminal block is plugged correctly		(3). Whether the terminal block is plugged correctly

			[[File:New_3D Touch_1.png]]

			[[File:New_3D Touch_2.png]]


Line 55:		Line 58:

	(3). Check whether the coil resistance is correct and cannot be broken		(3). Check whether the coil resistance is correct and cannot be broken

			[[File:New_3D Touch_3.png]]

			[[File:New_3D Touch_4.png]]


			[[File:New_3D Touch_5.png]]

			[[File:New_3D Touch_6.png]]

Admin at 09:33, 4 March 2025

2025-03-04T09:33:36Z

← Older revision		Revision as of 09:33, 4 March 2025
Line 30:		Line 30:

	Please refer to the following video https://www.youtube.com/watch?v=YmXwFmB4qys		Please refer to the following video https://www.youtube.com/watch?v=YmXwFmB4qys


			5.Troubleshooting

			1. Fault phenomenon: the light is not on,

			Failure Analysis:

			(1). Check whether the direction of the power cord is plugged in correctly, and the line sequence of the machine should be consistent with 3DTOUCH

			(2). Whether the power cord is disconnected

			(3). Whether the terminal block is plugged correctly



			2. Fault phenomenon: flashing red light

			Failure Analysis:

			(1). Check whether the fastening bolts are locked in place, and adjust the fastening bolts up and down appropriately

			(2). When powering on, the probe should jump up and down, and finally retract, and the probe will be smoothly discharged

			(3). Check whether the coil resistance is correct and cannot be broken

Admin at 03:27, 4 July 2024

2024-07-04T03:27:04Z

← Older revision		Revision as of 03:27, 4 July 2024
Line 17:		Line 17:


	4.~~3Dtouch~~ installation precautions:		4.installation precautions:

	1. The 3DTouch line sequence diagram is as follows. After installation, confirm whether the LED light is on and whether the 3Dtouch can be extended/retracted normally.		1. The 3DTouch line sequence diagram is as follows. After installation, confirm whether the LED light is on and whether the 3Dtouch can be extended/retracted normally.

Admin at 03:26, 4 July 2024

2024-07-04T03:26:03Z

← Older revision		Revision as of 03:26, 4 July 2024
Line 16:		Line 16:


	3Dtouch installation precautions:
			4.3Dtouch installation precautions:

	1. The 3DTouch line sequence diagram is as follows. After installation, confirm whether the LED light is on and whether the 3Dtouch can be extended/retracted normally.		1. The 3DTouch line sequence diagram is as follows. After installation, confirm whether the LED light is on and whether the 3Dtouch can be extended/retracted normally.

Line 25:		Line 27:
	2. Installation height problem: The nozzle presses the hot bed or the leveling failure is caused by the incorrect installation height of the 3Dtouch. The 3Dtouch installation height or adjustment height standard is: the 3dtouch probe is 2mm higher than the nozzle position when retracted.		2. Installation height problem: The nozzle presses the hot bed or the leveling failure is caused by the incorrect installation height of the 3Dtouch. The 3Dtouch installation height or adjustment height standard is: the 3dtouch probe is 2mm higher than the nozzle position when retracted.

	[[File:3D_Touch3.~~png~~]]		[[File:3D_Touch3.jpg]]

	Please refer to the following video https://www.youtube.com/watch?v=YmXwFmB4qys		Please refer to the following video https://www.youtube.com/watch?v=YmXwFmB4qys

Admin at 03:24, 4 July 2024

2024-07-04T03:24:38Z

← Older revision		Revision as of 03:24, 4 July 2024
Line 16:		Line 16:


	4.3Dtouch installation precautions:		3Dtouch installation precautions:
	1. The 3DTouch line sequence diagram is as follows. After installation, confirm whether the LED light is on and whether the 3Dtouch can be extended/retracted normally.		1. The 3DTouch line sequence diagram is as follows. After installation, confirm whether the LED light is on and whether the 3Dtouch can be extended/retracted normally.

	[[File:3D_Touch1.png]]		[[File:3D_Touch1.png]]
	~~(Figure 2)~~
			[[File:3D_Touch2.png]]

	2. Installation height problem: The nozzle presses the hot bed or the leveling failure is caused by the incorrect installation height of the 3Dtouch. The 3Dtouch installation height or adjustment height standard is: the 3dtouch probe is 2mm higher than the nozzle position when retracted.		2. Installation height problem: The nozzle presses the hot bed or the leveling failure is caused by the incorrect installation height of the 3Dtouch. The 3Dtouch installation height or adjustment height standard is: the 3dtouch probe is 2mm higher than the nozzle position when retracted.
	~~(Figure 3)~~
			[[File:3D_Touch3.png]]

	Please refer to the following video https://www.youtube.com/watch?v=YmXwFmB4qys		Please refer to the following video https://www.youtube.com/watch?v=YmXwFmB4qys

Admin at 03:21, 4 July 2024

2024-07-04T03:21:04Z

← Older revision		Revision as of 03:21, 4 July 2024
Line 14:		Line 14:
	3.Please click the link below to download the firmware with 3D TOUCH and refresh it.https://www.geeetech.com/download.html		3.Please click the link below to download the firmware with 3D TOUCH and refresh it.https://www.geeetech.com/download.html
	[[File:W80.png]]		[[File:W80.png]]


			4.3Dtouch installation precautions:
			1. The 3DTouch line sequence diagram is as follows. After installation, confirm whether the LED light is on and whether the 3Dtouch can be extended/retracted normally.

			[[File:3D_Touch1.png]]
			(Figure 2)
			2. Installation height problem: The nozzle presses the hot bed or the leveling failure is caused by the incorrect installation height of the 3Dtouch. The 3Dtouch installation height or adjustment height standard is: the 3dtouch probe is 2mm higher than the nozzle position when retracted.
			(Figure 3)
			Please refer to the following video https://www.youtube.com/watch?v=YmXwFmB4qys

Admin: /* Warnning */

2024-07-04T03:18:51Z

Warnning

← Older revision		Revision as of 03:18, 4 July 2024
Line 4:		Line 4:
	[[File:W78.png]]		[[File:W78.png]]
	2.Our company's A10, A20 and A30 series can use 3D TOUCH, I3 series is not suitable for 3D TOUCH.		2.Our company's A10, A20 and A30 series can use 3D TOUCH, I3 series is not suitable for 3D TOUCH.


	~~3.3Dtouch installation precautions:~~
	~~（1） The 3DTouch line sequence diagram is as follows. After installation, confirm whether the LED light is on and whether the 3Dtouch can be extended/retracted normally.~~
	~~[[File:3D_Touch1.png]]~~
	~~(Figure 2)~~
	（2） Installation height problem: The nozzle presses the hot bed or the leveling failure is caused by the incorrect installation height of the 3Dtouch. The 3Dtouch installation height or adjustment height standard is: the 3dtouch probe is 2mm higher than the nozzle position when retracted.
	~~(Figure 3)~~
	~~Please refer to the following video https://www.youtube.com/watch?v=YmXwFmB4qys~~

	==Installation tutorial==		==Installation tutorial==

Admin: /* Warnning */

2024-07-04T03:18:04Z

Warnning

← Older revision		Revision as of 03:18, 4 July 2024
Line 4:		Line 4:
	[[File:W78.png]]		[[File:W78.png]]
	2.Our company's A10, A20 and A30 series can use 3D TOUCH, I3 series is not suitable for 3D TOUCH.		2.Our company's A10, A20 and A30 series can use 3D TOUCH, I3 series is not suitable for 3D TOUCH.


			3.3Dtouch installation precautions:
			（1） The 3DTouch line sequence diagram is as follows. After installation, confirm whether the LED light is on and whether the 3Dtouch can be extended/retracted normally.
			[[File:3D_Touch1.png]]
			(Figure 2)
			（2） Installation height problem: The nozzle presses the hot bed or the leveling failure is caused by the incorrect installation height of the 3Dtouch. The 3Dtouch installation height or adjustment height standard is: the 3dtouch probe is 2mm higher than the nozzle position when retracted.
			(Figure 3)
			Please refer to the following video https://www.youtube.com/watch?v=YmXwFmB4qys

	==Installation tutorial==		==Installation tutorial==

Admin: /* Installation tutorial */

2023-06-19T08:55:45Z

Installation tutorial

← Older revision		Revision as of 08:55, 19 June 2023
Line 6:		Line 6:

	==Installation tutorial==		==Installation tutorial==
	1.1. Check whether the assembly parts of 3D TOUCH are complete~~. The shipping list of the two models of 3D TOUCH is below~~.https://www.geeetech.com/index.php?main_page=advanced_search_result&search_section=products&search_in_description=0&keyword=3d+touch&submit=		1.Check whether the assembly parts of 3D TOUCH are complete. https://www.geeetech.com/index.php?main_page=advanced_search_result&search_section=products&search_in_description=0&keyword=3d+touch&submit=

	[[File:W79.png]]		[[File:W79.png]]